Save the Booter options and Select Boot Now. Set Serial Ports to Serial Console on Modem. Open the Booter and set Boot options to boot Single User (Also check the scsi id of your disk. Once completed, select Build Devices from the installer and then quit the installer. The KERN_GENERIC.TGZ works fine.Īfter adding all desired sets, click Done and go for lunch. Make sure to also select and add a kernel. Next, start the Installer and navigate to Mac68K/BINARY/SETS and select the software sets you want to install. Start MKFS, select the scsi id of the hard disk to partition and format the usr and swap partitions. Into a folder on your Mac OS installation. On the installation iso, go to the Mac68K/Installation/Misc folder and copy: When you run qemu-aux.bat, qemu boots from the bootfloppy image, which in turn starts the A/UX installation.įor more information about adding scsi disk drives and scsi cdrom drives, see the section “ About disks, the scsi-id and boot order” earlier in this guide. drive file=AUX301.iso,format=raw,media=cdrom,if=none,id=cd0 drive file=AUX3.img,media=disk,format=raw,if=none,id=hd0 ^ drive file=AUXBootfloppy.img,media=disk,format=raw,if=none,id=fd0 ^ drive file=pram-aux.img,format=raw,if=mtd ^ Open your favorite text editor and create a file called qemu-aux.bat with the following content: This boot floppy also contains the AWS Tune-up 2.0 software that can be applied after upgrading the initial installation of A/UX 3.0.1 to 3.1 Qemu-img.exe create -f raw pram-aux.img 256bĭownload a boot floppy image named AUXBootfloppy.img from here: Qemu-img.exe create -f raw -o size=2G AUX3.img You'll have to source a rom file yourself. The A/UX related files can all be found here: but the files have to be unpacked with e.g. –drive file=MacOS8.0.iso,media=cdrom,if=none,id=cd0 Starting qemu-system-m68k to install Mac OS 8 and run it The same is true for a cdrom entry in your batch file: –device scsi-cd,scsi-id=3,drive=cd0 –drive file=MacOS8.0.img,media=disk,if=none,id=hd0
However, when a Startup Disk has been set, the scsi-id of that device is saved in the pram file and subsequent boots will attempt to boot from that scsi-id.Įach entry for a hard disk in your batch file uses two lines: –device scsi-hd,scsi-id=0,drive=hd0 When no Startup Disk has been set with the Startup Disk control panel, the Quadra will search for bootable devices from scsi-id 0 upwards and boot from the 1st bootable device it finds.
You can therefore attach a mix of hard disk and cdrom images up to a maximum of 7 entries.Įach scsi-hd or scsi-cd has to have a different scsi-id and a different drive name. However, scsi-id 7 is reserved for the Quadra itself. The SCSI controller allows 8 devices (numbered from 0-7) to be connected. The emulated Quadra uses SCSI to connect hard disks and CD roms. Save qemu-macos.bat About disks, the scsi-id and boot order Make sure there is one space before the ^ and no space behind it. Note:: To enable using multiple lines in the batch file end all lines except the last one with a ^. drive file=MacOS8.0.iso,media=cdrom,if=none,id=cd0 drive file=MacOS8.0.img,media=disk,format=raw,if=none,id=hd0 ^ drive file=pram-macos.img,format=raw,if=mtd ^ Open your favorite text editor and create a batch file called qemu-macos.bat with the following content: Qemu-img.exe create -f raw pram-macos.img 256b Qemu-img.exe create -f raw -o size=2G MacOS8.0.img Otherwise Mac OS will not boot after installation. Note: If you create a disk image larger than 2Gb, you will have to partition the disk so the first partition is 2Gb or less in size. Open a command prompt and navigate to your Qemu folder. Create a pram disk image to hold information about the system, such as screen resolution, scsi boot order.
0 kommentar(er)
